WaveTinkerbrowser audio studioSearch tools/Chain effects

Speaker Test (Headphone Test)

Press play and listen: the sound should jump to the left side, then to the right. If it does, both channels are wired and working. Then check the polarity of a speaker pair, sweep the whole frequency range and find out how low your speakers or headphones really go.

  • Free, no sign-up
  • Runs on your device
  • Best with headphones
  1. Turn the volume downSet your device volume low before the first sound. Test noise and tones are steady, so they can feel louder than music at the same setting.
  2. Play left, then rightPress Play left, then right: the sound plays twice on the left channel and twice on the right. The Left, Both and Right buttons repeat any one of them.
  3. Check phase and rangeCompare the two polarity buttons, run the sweep from 20 Hz to 20 kHz, and try the bass tones to hear where your speakers give up.

Updated

What the left and right test proves

Stereo audio is two separate signals, one for each side. The Left and Right buttons send sound to exactly one of them, with silence on the other, so a correct setup puts the left sound only in the left speaker or ear cup. If it comes out of both, something on the way is mixing the channels down to mono; if it comes out of the wrong side, the plugs or the settings are swapped.

Swapped sides are common with desk speakers, where the cable from the right output ends up on the left box, and with headphones worn backwards. Most headphones mark the left cup with an L, sometimes with a raised dot or a colored ring on the cable. Car and home stereos have a balance control that can push everything to one side; set it to the center before you start.

Mono output is the second common surprise. Phones and laptops have an accessibility switch, usually called Mono audio, that folds both channels into one so that people who hear with one ear miss nothing. It is useful when you need it, but while it is on every left and right test sounds centered. A Bluetooth speaker that is a single box also plays both channels from the same drivers, so the test cannot separate them there.

Both (center) plays the same sound on the two channels at equal level. On a well-placed pair of speakers it should seem to come from the point halfway between them, even though nothing is there. That phantom center is what holds a singer in the middle of a mix, and it only forms when both sides play at the same level and in the same polarity.

Headphone test: fit, sides and balance

A headphone test starts with the sides and then the balance. Play Left and Right a few times and ask whether the two sound equally loud. A slightly weaker side usually means one ear cup sits less tightly; press it gently against your head and listen again. If one side stays far quieter whatever you do, a cable, a plug or a driver is failing, most often at the bend where the cable leaves the plug.

Wireless earbuds add their own issues. Each bud has its own battery and its own radio link, so one can drop out, lag behind or keep an older volume setting. If a single bud fails the left and right check, put both back in the case, close the lid, wait a few seconds and pair again. Earbuds that sound thin on both sides often just need a larger tip: a tip that does not seal lets the bass leak out of your ear.

Pink noise is the best sound for judging balance because it spreads equal energy over every octave, so your ear has no single tone to lock onto. The chime is easier to place and shows the side more clearly on small speakers. The 1 kHz tone is the usual reference level in audio work, a simple way to compare whether both sides reach the same loudness.

Keep the level modest. A steady noise or tone tires the ear faster than music, and long exposure at a high level can damage hearing, so a few seconds at a comfortable volume are all this needs.

Polarity: in phase and out of phase

Every speaker cone moves out on the positive half of the signal and back in on the negative half. If one speaker in a pair is wired with plus and minus swapped, it moves in while its partner moves out. The two cones then work against each other, and the low frequencies, where both speakers play almost the same thing, partly cancel.

The two polarity buttons make that audible. In phase plays identical noise on both channels; it should sound solid and sit in the middle. Out of phase inverts the right channel on purpose; it should sound wide, vague and thin, as if it came from around your head rather than from in front of you. If In phase matches that second description and Out of phase sounds solid, one speaker is wired backwards: swap the two wires on the back of one speaker only.

The difference is strongest when you sit between the speakers at the same distance from each. On headphones it is still there but subtler, because each ear hears only its own side; out of phase tends to feel like pressure inside the head rather than missing bass. Laptop speakers a few inches apart barely show it at all.

Sweep: where your speakers start and stop

The sweep rises from 20 Hz to 20 kHz in 24 seconds and spends the same time on every octave. Watch the number while you listen. On small speakers the tone appears only after a few seconds, somewhere between 80 and 200 Hz, because a small cone cannot move enough air for deep bass. Near the top it fades out again: either the tweeter stops, or your ears do.

Telling those two apart is the hard part. Hearing at high frequencies declines with age and with noise exposure, and many adults hear little above 15 kHz, so a tone that vanishes at 16 kHz may be your ears rather than the speaker. Repeat the sweep on headphones you trust; if the tone lasts longer there, the speaker is the limit. For your own range, the hearing check has a separate sweep with an ear-by-ear option.

Listen for rattles and buzzes on the way up. A loose panel, a grille or a cable touching the cabinet buzzes at one particular frequency and falls silent above and below it. The sweep finds that spot in seconds, which makes it a handy sound test after you mount speakers on a wall or a shelf.

Peaks and dips in loudness along the way are normal. Rooms reinforce some low notes and cancel others depending on where the speakers and your ears are, so the same pair can sound boomy at 60 Hz in one corner and thin in another. Moving a speaker a foot away from the wall changes this more than any setting does.

Bass check: 30 to 150 Hz

The bass buttons play single tones for two seconds each, from 30 Hz up to 150 Hz. They answer one plain question: which of these does your system actually reproduce? A good subwoofer plays all six. Floor-standing speakers usually reach 40 Hz, bookshelf speakers and good headphones go down to about 60 Hz, and laptops and phones often start near 150 Hz and fake the rest.

The faking is clever. Small devices play the overtones of a bass note and the brain fills in the missing fundamental, so you hear a bass line even when the speaker produces nothing at its real pitch. A pure low tone has no overtones, so on those speakers the 30 and 40 Hz buttons give silence. That is not a fault; it is physics and a small box.

With a subwoofer, the bass tones also show the crossover. Play 80 Hz and rest a hand on the subwoofer, then on the main speakers. Below the crossover the sub does the work; above it, the main speakers take over. A tone that suddenly drops in level between two neighboring buttons often points at a crossover set too low or a sub turned down.

Keep low tones short and quiet. Sub-bass carries a lot of energy, and a small speaker pushed hard at a frequency it cannot play can be damaged when its cone hits its limits. If you hear distortion or a flapping sound, stop at once and lower the level.

Before a call, on a laptop or a TV

Before a video call, the quickest check is the left and right test on the output your call app will use. The operating system keeps a default output device and call apps often keep their own, so a headset can be connected while the sound still goes to the laptop speakers. If you hear nothing at all, look at the output device in the system sound menu first, then in the browser.

On a laptop, the speaker test is mostly about balance and rattles. Many laptops have one speaker on each side of the keyboard or under the front edge, and a blocked grille, a soft surface or a cracked case changes the sound of one side. Running the sweep with the laptop on a hard table and then on your lap shows how much the surface matters.

TVs and sound bars connected over HDMI often process the signal: virtual surround, dialogue boost or a night mode can widen or narrow the left and right test and change the phase test completely. Switch those modes off, test, then switch back on what you like. This page plays plain stereo only; it cannot address the center, surround or height speakers of a home cinema.

What stays on your device

The test sounds are generated by your browser as you press each button. There are no audio files to fetch, and the page never opens the microphone. The Volume slider sets only the level of the test sounds, not your system volume, so set the system volume first and fine-tune here.

Your choices are not saved: close the tab and the next visit starts with the default sound and level. To check the other half of a call, the mic test shows whether your microphone picks you up and plays a short recording back.

Frequently asked questions

How do I test my speakers left and right?

Press Play left, then right. The sound should play twice on the left and twice on the right. If both sides play at once, look for a Mono audio setting; if the sides are swapped, swap the cables or turn the headphones around.

What does a headphone test check?

That both sides of your headphones work, sit on the correct ears and play at the same level, plus how much of the frequency range they cover. Pink noise makes a difference in balance easiest to hear.

Why do I hear nothing at 30 or 40 Hz?

Most phone, laptop and small desk speakers cannot reproduce tones that low; they suggest bass with overtones instead. A subwoofer, floor-standing speakers or good headphones usually play them.

How can I tell if my speakers are out of phase?

Compare the two polarity buttons. In phase should sound solid and centered, out of phase wide and thin. If you hear it the other way around, the plus and minus wires of one speaker are swapped.

Does this test surround sound?

No, it tests the two stereo channels. A surround receiver plays the left and right sounds through its front speakers, or spreads them around if an upmix mode is on.

Is it safe to play test tones?

At a moderate level and for a few seconds, yes. Start with the system volume low and raise it slowly; steady tones and noise can damage hearing and small speakers when they are loud.

What each part of the test can tell you

Where a speaker usually stops and what lives in each part of the sweep:

Typical behaviour of consumer speakers and adult hearing; your own equipment and ears decide.
FrequencyWhat it isWho plays it
30–40 Hzdeep sub-basssubwoofers and large floor speakers; phones and most laptops play almost nothing
60–80 Hzthe body of a kick drumbookshelf speakers and good headphones
100–150 Hzupper bassmost laptops and earbuds, thinner on phones
1 kHzthe middle of the rangeevery speaker; the level reference of the 1 kHz test tone
10–15 kHzair and cymbal shimmermost speakers; many adult ears hear less up here
15–20 kHzthe top of the sweeptweeters and headphones; often inaudible after about age 25

Tools that pick up where this one stops.